Concrete materials, epoxy floor coatings, concrete sealers North Carolina
Concrete materials, epoxy floor coatings, concrete sealers North Carolina

Charlotte NC: (704) 333-4235
Raleigh NC: (919) 794-7442

SR2 Water-Based Penetrating Stain Resistor

SR2 Water-Based Penetrating Stain Resistor

• Non-topical, penetrating sealer
• VOC exempt & non-flammable
• Treated surfaces ‘breathe’ and do not trap moisture

• Excellent stain repellency for residential, commercial

• Compatibility to bond with Ameripolish Color System components to protect the color in slab
• Provides a chance to clean up spills before they stain or etch a surface

Turning Point Supply’s SR2 Water-Based Stain Resistor Exclusive Pricing:

 

Product Part # MSRP OUR PRICE 
(1 gal RTU) SR2WB-1 $76.00 $58
(5 gal RTU) SR2WB-5 $380.00 $291
(30 gal RTU) SR2WB-30 $2,280.00 $1595
(55 gal RTU) SR2WB-55 $4,.180.00 $2900

Most products are In Stock in one of our store locations. Call for details. 

MPN: SR2WB-1-250 SKU: SR2-1-250 Category: Brand:
SR2 Water-Based Penetrating Stain Resistor

SR2 Water-Based Penetrating Stain Resistor

Product Description

Ameripolish® SR²™ is a penetrating stain repellent specifically formulated to protect polished, dyed, and non-dyed concrete from oil and water-based stains. The water and oil repelling qualities of SR²™ provide superior stain protection on most substrates. SR²™ can be used as a standalone product but, to obtain optimum performance, Ameripolish® SR²™ is recommended for use with Ameripolish® 3D HS or HSL Densifiers.

Ameripolish® SR2™ is ideal to be used on new or existing polished concrete and exposed concrete flooring.

Dilution & Coverage
Ameripolish® SR2™ is shipped Ready to Use (RTU) and should not be mixed with any other chemical. The approximate coverage rate is 3,000 - 5,000 sqft per gallon.

Application:

The ambient temperature should be 40-90°F (4-32°C) during application. Do not apply over 90°F (32°C); avoid application on hot, windy days. SR²™ provides the best protection when applied in a light “film” coat.

1. Spray a light mist of SR²™ onto the concrete surface and immediately spread evenly with an Ameripolish® microfiber pad.  Apply enough material to keep the surface wet for about a minute before penetrating; attain 100% coverage, without either dry streaking or puddling.
2. Mop out any puddles thoroughly until they completely penetrate the surface.
3. NOTE: For Vertical Surfaces apply enough material to thoroughly wet the surface in a uniform application.  Do not allow a rundown below the spray pattern.
4. Burnish with a high-speed burnisher, fitted with a 3000 grit or finer diamond-impregnated pad, or auto-scrub with a white pad to remove surface haze.
5. Chemical resistance gains strength over time. Avoid etching agents for seven days if possible. Areas that will be exposed to excessive, ongoing spills or extremely porous substrates may benefit from a second application of SR²™ before burnishing.
The floor is ready for light foot traffic when SR²™ is dry to touch; protect treated surfaces from traffic for at least one hour. SR²™ gains its chemical resistance and water repellency after 24 hours, and it cures fully within seven days. However, even after becoming densified and polished, concrete is still a porous substrate.

Download Now

Loader Loading...
EAD Logo Taking too long?

Reload Reload document
| Open Open in new tab

Download Now

Loader Loading...
EAD Logo Taking too long?

Reload Reload document
| Open Open in new tab

Related products