Gloss Finish Water Base Floor Polyurethane Clear and Colored

Gloss Finish Water Base Floor Polyurethane Clear and Colored

Gloss Finish Water Base Polyurethane

UWB Gloss is a high gloss water-based polyurethane concrete floor sealer that can be applied directly to concrete – no epoxy primer needed. UWB Gloss provides incredibly good color enhancement with excellent healing properties for reducing roller lines. The product is tintable in 14 colors using UWB-Tint.

Packaging:
1.25-Gallon Kits

Product Request

The unique formula used in Industrial, Commercial, and Residential applications such as:

  • Warehouse and Office Spaces
  • Retail Flooring and Restaurants
  • Garage and Basement
  • Topcoat over Metallic and Stains

Product Advantages:

  • Low Viscosity
  • Excellent Penetration and Surface Adhesion
  • 45 Minute Pot Life
  • Excellent Heal for Reduced Roller Lines
  • Low Odor, Indoor Application Friendly

ENVIRONMENTAL CONDITIONS: Application of product should be placed between Substrate - 50° to 80° F

The substrate temperature during application and curing must be within the limits listed above. Ambient temperature should not be used to judge application temperature. The use of a laser temperature gauge is necessary to find the substrate temperature. If the product is applied outside of these temperature parameters, the product may not cure properly and will not meet specifications in hardness or chemical resistance.

Tinting Instructions:

UWB-Gloss is a clear water-base polyurethane. If an opaque surface is required, UWB-Tint is available in six standard colors. Add pigment to Part A before blending with Part B.

Mixing Instructions:

If less than full kits will be mixed, each component should be mixed thoroughly with individual tools. Using the same tool to mix part A and Part B will cause contamination and ruin the material being saved for future use. UWB is to be mixed at a ratio of 4 parts A to 1 part B. In clean measuring containers pour the correct ratio in and mechanically mix for 3 minutes. DO NOT USE A STIR STICK! The amount of material mixed should only be what can be utilized within the pot life recommendations of the product. A jiffy style mixing paddle is recommended to limit the introduction of air while combining Part A and Part B.

Application Instructions:

Do not mix more material than can be spread during the pot life of the product. Discontinue application if the material gets sticky and isn’t spreading smoothly. UWB-Gloss should be applied with a roller pan and roller. 18” rollers with a 3/8” nap are best for moving the material efficiently while not leaving roller lines. The product will be white during application and clear during cure. Tray liners are recommended so older material does not get mixed in with new product. Change rollers immediately if they start to stick to the product being placed.  UWB-Gloss is meant to be a thin-mil system. Do not let it puddle or get too thick.

RECOAT: Recoat windows are directly affected by the ambient surface temperature. The maximum recoat window will fall between 6 and 12 hours. It is important to apply additional coatings as early in the recoat window as possible for the best results. If the recoat window has passed it is critical to thoroughly abrade the surface with 100 to 120 grit sanding screens. Thoroughly clean the existing coating before abrading to remove potential contaminants. Vacuum dust off the floor then follows by wiping down the floor with lint-free cloths dampened with water. Allow to completely dry before applying an additional coat at the recommended rate.

Cured Physical Properties:

Flexibility – ASTM D1737 - Pass
Pendulum Hardness – ASTM D-4336 - 175
Abrasion Resistance, 1000 gm load 1000 cycles – ASTM D4060 – 38 to 40 mg loss
Water Resistance - Excellent
Gloss, 60 Degree – ASTM E97 – 88

Chemical Resistance Chart:

E = Excellent 
D = Discolors 
NR = Not Recommended
Brake Fluid – E
Chlorinated Water – E
Clorox 10% - E
Diesel Fuel – E
Gasoline – E
Hydraulic Fluid – E
Hydrochloric Acid 20% - E
Isopropyl Alcohol – E
MEK – D
Methanol – E
Motor Oil – E
Muriatic Acid 10% - E
Nitric Acid 10% - NR
Phosphoric Acid – E
Skydrol – E
Sodium Hydroxide 25% - E
Sugar Water – E
Sulfuric Acid 10% - E
Transmission Fluid – E
Urine – E
Vinegar 5% - E
Water – E
Wine – E
Xylene - E

Download Now


Loader Loading...
EAD Logo Taking too long?

Reload Reload document
| Open Open in new tab

Download

Download Now


Loader Loading...
EAD Logo Taking too long?

Reload Reload document
| Open Open in new tab

Download

Download Now


Loader Loading...
EAD Logo Taking too long?

Reload Reload document
| Open Open in new tab

Download

Download Now


Loader Loading...
EAD Logo Taking too long?

Reload Reload document
| Open Open in new tab

Download


Gloss Finish Water Base Floor Polyurethane Clear and Colored