ColorTec Acrylic™ Professional Grade Pigmented Outdoor Sealer

ColorTec Acrylic™ Professional Grade Pigmented Outdoor Sealer

ColorTec Acrylic™ is a single-component, 30% acrylic solids, 600 g/L, color sealer developed for SureCrete overlays or any cement-based product. It is vapor permeable yet reduces the
penetration of fluids into the surface. ColorTec Acrylic will enhance the beauty and improve stain and abrasion resistance for driveways, garage floors, patios, walkways, pool decks, stucco, and concrete block. Pigments are specifically formulated for UV stability, will not blush, and retain long gloss retention.

MPN: N/A SKU: ColortecAcrylic-1-5 Category: Brand:

ColorTec Acrylic™ Professional Grade Pigmented Outdoor Sealer

Product Description

Test ASTM (if applicable)
Results
Blush 4 hr. dry /
18 hr. immersion
No blush
Adhesion D-3359
Dry Concrete Excellent
Wet Concrete Excellent
QUV accelerated
weather testing
G-53 250 hr. –
no blistering,
no yellowing
Abrasion
resistance
12.5 grams loss
Block resistance D-4946 Excellent
Heat stability @
120°F (49°C)
D-1849 Excellent
Film formation @
40°F (4°C)
Passed
Water absorption 2.4 g /m³
Pencil hardness D-3363 HB-H
Hot tire pick-up Passed*

 

Planning
1. Product is flammable. For Interior applications, turn off all fuel-burning appliances and pilot lights.
2. Provide ventilation so that vapors do not accumulate.
3. Select appropriate PPE (personal protection equipment). Use
of a NIOSH approved respirator may be required. Refer to SDS.
Mask all areas requiring protection.
Temperature/weather
1. Avoid application on cold or hot days or during
wet, foggy weather.
2. Apply with ambient and surface temperatures ranging above
50°F (10°C) and below 90°F (32°C), and that will remain within
ranges for at least 24 hours following application.
3. Do not apply outside if precipitation is forecast within 24
hours of application.
4. Substrate must be dry throughout all steps.
Mixing
Mechanically mix with a “Jiffy” style mixer blade for 3 minutes at
medium speed for complete dispersal of pigments. Use caution
not to entrain air during mixing.
First coat
Rolling
1. Utilize a bucket grid to apply in a thin film.
2. Roller covers require a solvent-resistant core.

3. The correct nap size varies due to texture. For example ¾” is
recommended for heavily textured patterns, while ¼” mohair is
recommended for very smooth surfaces.
4. Do not allow puddling.
5. Exercise care to eliminate roller tracks through back rolling.
Airless Spraying
1. Airless sprayer should be capable of a minimum .5 GPM discharge.
2. Tip size should be approximately .015” - .019” with a 65° fan.
3. For horizontal surfaces utilize an 8” – 10” extension.
4. Maintain a wet edge between passes.
Pump-up Sprayer
1. Select solvent resistant sprayer.
2. Select fan or cone tip as preferred that can pass 30% solids product.
3. Have sufficient tips on hand to allow clean-up that will not interrupt application.
4. If necessary, backroll sprayed area to lay product flat.
When the first coat can be walked on, it may receive a second
coat. A second coat is desired to accomplish complete hide (i.e., complete and even color coverage). Customarily two thin coats achieve the best performance.
Second Coat
Applies identical to the first coat.
Allow 24 hours of cure time before foot traffic.
Allow 72 hours of cure time before vehicular traffic.

Download Now


Loader Loading...
EAD Logo Taking too long?

Reload Reload document
| Open Open in new tab

Download Now


Loader Loading...
EAD Logo Taking too long?

Reload Reload document
| Open Open in new tab

Download Now


Loader Loading...
EAD Logo Taking too long?

Reload Reload document
| Open Open in new tab

Product Enquiry

%d bloggers like this: