Clear Sealers for Indoor Floors | Clear Interior Floor Coatings

DK400WB | Water Based Clear Polyurethane Concrete Floor Sealer

SureCrete Design Products DK400WB water-based clear floor polyurethane top coat is available in either a gloss or satin finish. DK400WB is formulated as a highly durable transparent flooring protective coating for interior commercial or residential applications with low VOC properties. The clear water-based floor polyurethane is a 2 component 57% solids, acrylic polyurethane designed as a non-yellowing clear coating for concrete, cement-based overlays, or as a top coat on epoxy systems. The commercial grade clear finish topcoat is available in gloss or satin finishes provides the durability of a solvent base system with the ease and safety of a low VOC (72 g/L) water base system. As a vertical wall coating, DK400WB enhances anti-graffiti properties. DK400WB water based polyurethane is ideally suited for both commercial and residential flooring anywhere in North Carolina and South Carolina: aircraft hangars, clean room floors, manufacturing facilities, warehouses, bars, clubs, retail stores, automotive showrooms, residential interiors, garage floors, stadiums, or any high traffic area where an exceedingly resilient floor is desired.

Specifications and properties of DK400WB Clear Water Based Polyurethane Concrete Floor Coating from SureCrete Design Products

Coverage: Approximately 400-500 square foot per gallon, per coat (varies based on substrate porosity and application methods)
VOC Rating: less than 72 g/L
Solids Content: 57%
Pot Life: approximately 30 minutes
Shelf Life: 1 year in original unopened container
Ready for recoat: 6-10 hours
Light Duty Use: 24 hours
Heavy Traffic Ready: 3 days
Full Cure: 5-7 days
Appearance (cured): Clear Gloss or Satin
Appearance (wet): Milky Liquid
Water Resistance: Excellent beads water
Mechanical Stability: Excellent
Light Stability: Excellent
Diluent: Water
Odor: Sweet Acrylic
Application Temperature: 50 – 90 degrees Fahrenheit

Chemical Resistance
Gasoline, no effect at 24 hrs
Diesel Fuel, no effect at 24 hrs
Kerosene, no effect at 24 hrs
Brake Fluid, softens/discolors at 24 hrs
Skydrol, dulls at 24 hrs

[return to top]

DK400 | Solvent Aliphatic High Gloss Polyurethane Concrete Floor Coating

DK400 solvent based clear high gloss floor aliphatic polyurethane is a two component 51% solids, acrylic aliphatic polyurethane designed as a non-yellowing clear coating for interior concrete, concrete overlays, or as a clear top finish coat on epoxy systems. The high-gloss clear top coat provides the premier balance of strength, added UV stability, flexibility, chemical and scratch resistance that is both user-friendly and extremely durable. DK400 Solvent Aliphatic Polyurethane clear topcoat is one of the most mechanically and chemically resistant coatings available on the market in North Carolina and South Carolina today.

Specifications and properties of DK400 Solvent Aliphatic Polyurethane Concrete Floor Coating from SureCrete Design Products

Coverage: Approximately 300-400 square foot per gallon, per coat (varies based on substrate porosity and application methods)
VOC Rating: less than 435 g/L
Solids Content: 51%
Pot Life: approximately 60 minutes
Shelf Life: 1 year in original unopened container
Ready for recoat: 6-8 hours
Light Duty Use: 24 hours
Heavy Traffic Ready: 3 days
Full Cure: 5-7 days
Appearance (cured): Clear Gloss
Appearance (wet): Clear
Water Resistance: Excellent, beads water
Mechanical Stability: Excellent
Light Stability: Excellent
Direct Impact: 30 inch/pounds
Reverse Impact: 6 inch/pounds
Hardness: Pencil 4H, Konig 100
Diluent: Hydrocarbons
Odor: Solvent
Application Temperature: 50 – 90 degrees Fahrenheit

Chemical Resistance
MEK (methyl ehtyl ketone), slightly softens at 3 mins, softens at 1 hr, blisters at 24 hrs
Xylene, no effect at 3 mins or 1 hr, softens at 24 hrs
Toulene, no effect at 3 mins, slightly softens at 1 hr, softens at 24 hrs
Mineral Spirits, no effect at 3 mins, 1 hr or 24 hrs
Ethanol, no effect at 3 mins, softens at 1 hr and 24 hrs
1,1 – trichloroethane, no effect at 3 mins, 1 hr or 24 hrs
5% sodium hydroxide, no effect at 3 mins, 1 hr or 24 hrs
50% sodium hydroxide, no effect at 3 mins, 1 hr or 24 hrs
5% sulfuric acid, no effect at 3 mins, 1 hr or 24 hrs
50% sulfuric acid, no effect at 3 mins, 1 hr or 24 hrs
5% hydrochloric acid, no effect at 3 mins, 1 hr or 24 hrs
20% hydrochloric acid, no effect at 3 mins, 1 hr or 24 hrs
5% nitric acid, no effect at 3 mins, 1 hr or 24 hrs
20% nitric acid, no effect at 3 mins and 1 hr, blisters at 24 hrs
5% ammonia, no effect at 3 mins, 1 hr or 24 hrs
Gasoline, no effect at 3 mins, 1 hr or 24 hrs
Diesel Fuel, no effect at 3 mins, 1 hr or 24 hrs
Kerosene, no effect at 3 mins, 1 hr or 24 hrs
Brake Fluid, no effect at 3 mins and 1 hr, softens/discolors at 24 hrs
Skydrol, no effect at 3 mins and 1 hr, dulls at 24 hrs

[return to top]

SurfKoat 6000 WB Water Base Polyurethane Gloss User Friendly

Additional Info

Key Features and Typical Benefits

• Low viscosity allows for excellent substrate wetting and penetration
• Provides superior resistance to many common chemicals, solvents and hot tire pick up
• Excellent abrasion resistance that rivals many solvent based products
• Gloss finish and low odor make this ideal for many interior applications
• Can be tinted solid color using Kolour Koat Urapack-WB
• VOC compliant for most areas in the United States and Canada

Recommended Applications

• Grind and seal applications
• Over Heritage Stain and Kolour Dye
• Over other stain systems
• Garages and shops
• Showrooms and Offices
• Many interior applications where a low odor, gloss finish, abrasion resistant coating is required

Typical Properties and Technical Information

Solids / Active Content, percentage by weight: 40%

Dry Time, tack free: 5 – 6 hours

Dry Time, foot traffic: 16 – 20 hours

Dry Time, heavy traffic: 4 – 7 days

Re-coat Time Window: 6 – 12 hours

Application Temperature: 50 – 80 deg F

VOC Content: Less than 125 grams/Liter

Appearance, wet: Milky White

Appearance, dry: Clear and Gloss Finish

[return to top]

SurfKoat MCU-55 Moisture Cure Urethane Single Component

Key Features & Typical Benefits

Redesigned formulation offers superior gloss and leveling over smooth, coated floors.

Recoatable formula makes adding additional coats easy.

Superior chemical resistance and unmatched hardness provide protection other coatings can’t offer.

UV stability allows this to be used in areas saturated by the sun throughout the day.

Easy to use, a one-component system makes this more user-friendly than many traditional urethanes.

Recommended Applications

Effective on applications such as…

Auto Service Centers

Laboratories

Aircraft Hangars

Garages

Kennels / Veterinary Clinics

Maintenance I Chemical Rooms

Showrooms

Epoxy and Chip System Floors

Any other concrete surfaces where superior abrasion and chemical resistance are key.

[Return to Top]

DK120 | Clear Performance Polyaspartic Concrete Floor Coating

SureCrete Design Products DK120 Clear Polyaspartic Concrete Floor Coating is the best polyaspartic system available. DK120 is very user friendly with a longer open time and better heal than all other polyaspartic systems available in North Carolina and South Carolina from Spartacote, Smith Paints, Dur-A-Flex, General Polymers, PPG and other manufacturers. DK120 produces a very smooth finish with a fast recoat interval for reduced labor cost. The finish is highly chemical resistance and abrasion resistant making it the perfect clear interior concrete floor coating system for aircraft hangars, retail stores, grocery stores, garages, and other high traffic locations.

Specifications and properties of DK120 Performance Clear Polyaspartic Concrete Floor Coating from SureCrete Design Products

Coverage: Approximately 300-400 square foot per gallon, per coat (varies based on substrate porosity and application methods)
VOC Rating: less than 330 g/L
Solids Content: 67%
Pot Life: approximately 30 minutes
Shelf Life: 1 year in original unopened container
Ready for recoat: 1-2 hours (extended at low temperatures)
Light Duty Use: 3-4 hours (extended at low temperatures)
Heavy Traffic Ready: 24-36 hours (extended at low temperatures)
Full Cure: 1-2 days (extended at low temperatures)
Appearance (cured): Clear Gloss
Appearance (wet): Clear
Water Resistance: Excellent, beads water
Mechanical Stability: Excellent
Light Stability: Excellent
Odor: Aromatic
Application Temperature: 32 – 90 degrees Fahrenheit
Gardener direct / Reverse impact: More than 160 inch pounds
Taber Abrasion: 40-60 mg loss
QUV – A: less than 5.0 at 2,000 hours
Gloss Retention: More than 95% at 2,000 hours

Chemical Resistance:
MEK (methyl ehtyl ketone), no effect at 24 hours, fails at 7 days
Xylene, no effect at 24 hours, 7 days
Tap Water, no effect at 24 hours, 7 days
Mineral Spirits, no effect at 24 hours, 7 days
100% Ethanol, no effect at 24 hours, 7 days
10% Acetic Acid, no effect at 24 hours, fails at 7 days
50% Sodium Hydroxide, no effect at 24 hours, 7 days
85% Lactic Acid, no effect at 24 hours, fails at 7 days
50% Sulfuric Acid, no effect at 24 hours, 7 days
38% Hydrochloric Acid, no effect at 24 hours, 7 days
28% Ammonia, no effect at 24 hours, fails at 7 days
10% Sodium Chloride, no effect at 24 hours, 7 days
Gasoline, no effect at 24 hours, 7 days
Diesel Fuel, no effect at 24 hours, 7 days
Kerosene, no effect at 24 hours, 7 days
Brake Fluid, no effect at 24 hours, fails at 7 days
Skydrol, no effect at 24 hours, dulls at 7 days
Coffee, no effect at 24 hours, 7 days
Cola, no effect at 24 hours, 7 days
Grape Juice, no effect at 24 hours, 7 days
Ketchup, no effect at 24 hours, 7 days
Mustard, transient staining at 24 hours, 7 days
Clorox Bleach 5-10%, no effect at 24 hours, 7 days

[return to top]

DK180 | High Build Clear Polyaspartic Indoor Concrete Floor Coating

DK180 Clear Polyaspartic Concrete Floor Coating by SureCrete Design Products is a specially formulated 80% solids hybrid solvent based polyaspartic coating. DK180 Polyaspartic has a user-friendly extended pot life of approximately 20 minutes and the ability to create a moderate build single coat top coat. Turnaround time for a floor may be as little as 6 to 8 hours. Decorative vinyl flakes may be covered in a single coat with DK180 high build polyaspartic. DK180 provides a low VOC (less than 200 g/L), UV stable, penetrating, film forming, color enhancing, and high gloss, moderate build wear surface. The rapid cure time eliminates excessive waiting to return a floor to service. It is ideally suited for both commercial and residential settings anywhere in North Carolina and South Carolina: aircraft hangars, clean room floors, manufacturing facilities, warehouses, bars, clubs, retail stores, automotive showrooms, residential interiors, garage floors, stadiums, or any high traffic area where an exceedingly resilient floor is desired.

Specifications and properties of DK180 Clear Polyaspartic Concrete Floor Coating from SureCrete Design Products

Coverage: Approximately 150-200 square foot per gallon, per coat (varies based on substrate porosity and application methods)
VOC Rating: less than 200 g/L
Solids Content: 80%
Pot Life: approximately 20 minutes
Shelf Life: one year in original unopened container
Ready for recoat: Approximately 2 hours (extended at low temperatures)
Light Duty Use: 4-6 hours (extended at low temperatures)
Heavy Traffic Ready: Approximately 24 hours (extended at low temperatures)
Full Cure: 1-2 days (extended at low temperatures)
Appearance (cured): Clear Gloss
Appearance (wet): Clear
Water Resistance: Excellent, beads water
Mechanical Stability: Excellent
Light Stability: Excellent
Odor: Aromatic
Application Temperature: 32 – 90 degrees Fahrenheit
Gardener direct / Reverse impact: More than 160 inch pounds
Taber Abrasion: 40-60 mg loss
Gloss Retention: More than 95% at 2,000 hours

Chemical Resistance
MEK (methyl ehtyl ketone), no effect at 24 hours, fails at 7 days
Xylene, no effect at 24 hours, 7 days
Tap Water, no effect at 24 hours, 7 days
Mineral Spirits, no effect at 24 hours, 7 days
100% Ethanol, no effect at 24 hours, 7 days
10% Acetic Acid, no effect at 24 hours, fails at 7 days
50% Sodium Hydroxide, no effect at 24 hours, 7 days
85% Lactic Acid, no effect at 24 hours, fails at 7 days
50% Sulfuric Acid, no effect at 24 hours, 7 days
38% Hydrochloric Acid, no effect at 24 hours, 7 days
28% Ammonia, no effect at 24 hours, fails at 7 days
10% Sodium Chloride, no effect at 24 hours, 7 days
Gasoline, no effect at 24 hours, 7 days
Diesel Fuel, no effect at 24 hours, 7 days
Kerosene, no effect at 24 hours, 7 days
Brake Fluid, no effect at 24 hours, fails at 7 days
Skydrol, no effect at 24 hours, dulls at 7 days
Transmission Fluid, no effect at 24 hours, 7 days
Coffee, no effect at 24 hours, 7 days
Cola, no effect at 24 hours, 7 days
Grape Juice, no effect at 24 hours, 7 days
Ketchup, no effect at 24 hours, 7 days
Mustard, transient staining at 24 hours, 7 days
Clorox Bleach 5-10%, no effect at 24 hours, 7 days

[return to top]

Polykoat GL 90 LPL | 90% Solids Polyaspartic Polyurea Long Pot Life

Key Features and Typical Benefits

• Excellent long term wear capabilities allow for longer life without recoating.
• Polyaspartic floor coating material system with long pot life polyaspartic floor coating material properties
• Quick-dry time provides unmatched labor-saving capabilities above epoxies and polyurethanes.
• UV stability allows this to be used in areas saturated by the sun throughout the day.
• Excellent for use in the Rapid Cast Chip Floor System.
• It can be tinted for solid color applications with SurfKoat’s Kolour Koat Polypack.
• VOC compliant

Effective on applications such as:

• Garages
• Auto Service Centers
• Laboratories
• Cafeterias
• Many other interior concrete floors where a fast curing, high performance coating is needed

Specifications

• Solids Content – 90% by weight
• Dry Time, tack free – 2-3 hours
• Dry Time, foot traffic – 3-4 hours
• Dry Time, heavy traffic – 24 hours
• Recoat Time Window – 2-18 hours
• Application Temperature – 50-80 deg F
• VOC Content – less than 400 g/L
• Appearance, wet – clear, may show slight haze
• Appearance, dry – clear and high gloss

[return to top]

DK500 | Clear 100% Solids Epoxy Concrete Floor Coating

DK 500 is a clear floor epoxy 100% solids available in a standard, premium, and a thin viscosity options. SureCrete Design Products DK500 epoxy coating floor system, available from Turning Point Innovations in Charlotte North Carolina, can be used in a wide variety of applications such as high build clear coat for a host of decorative concrete systems, a primer coat and binder coat for DK Flakes and DK Metallics. The high performance, self-leveling characteristics of DK500 100% solids epoxy generate the premier balance of strength, flexibility, and chemical resistance that is both user-friendly and extremely durable.

Specifications and properties of DK500 Clear 100% Solids Epoxy Floor Coating from SureCrete Design Products

Coverage: 40-150 square foot per gallon per coat catalyzed product (varies widely based on application method)
VOC Rating: 0 g/L
Solids Content: 100%
Shelf Life: one year in original unopened container
Mixing Ratio: 2 parts A to 1 part B
Pot Life: 10-20 minutes
Ready for recoat: 6-8 hours (may be accelerated)
Light Duty Use: Approximately 16 hours
Heavy Traffic Ready: Approximately 24 hours
Full Cure: 5-7 days
Appearance (cured): High gloss sheen
Appearance (wet): Clear – Straw Color
Water Resistance: Excellent beads water
Mechanical Stability: Excellent
Light Stability: varies with selected hardener
Odor: Sweet
Adhesion: 400 PSI (concrete failure)
Abrasion Resistance (Tabor): 1,000 gm. load @ 500 cycles = 31 mg loss
Compressive Strength: 9,000 PSI
Application Temperature: 50 – 90 degrees Fahrenheit

Chemical Resistance
MEK, not recommended
Xylene, 8 hours splash spill
Gasoline, 2 hours splash spill
Butanol, 8 hours splash spill
Methanol, not recommended
Ethyl Alcohol, 8 hours splash spill
Skydrol, 2 hours splash spill
10% Sodium Hydroxide, long term immersion
50% Sodium Hydroxide, 2 hour immersion
Acetic Acid 5%, 2 hours splash spill
10% Sulfuric Acid, 8 hours splash spill
70% Sulfuric Acid, not recommended
10% Hydrochloric Acid, 8 hours splash spill
20% Nitric Acid, not recommended
Ethylene Glycol, 8 hours splash spill

[return to top]

250 HP Cyclo Epoxy 100% Solids Cyclo-Aliphatic Epoxy

Key Features and Typical Benefits

• Excellent for a variety of seamless, high build concrete flooring applications.
• Enhanced flow and leveling properties make this a favorite of flooring contractors.
• Use this product as the base coat and metallic coat in the Metallic FX flooring system.
• It can be tinted for solid color applications with SurfKoat’s Kolour Koat Epopack-HP.
• VOC compliant

Effective on applications such as:

• Auto Service Centers
• Warehouses
• Laboratories
• Aircraft Hangars
• Cafeterias
• Garages
• Quartz and Metallic Flooring applications

Specifications and Compliances

• Dried coating is USDA accepted
• Meets OTC, CARB, SCAQMD VOC restrictions
• Solids Content – 100%
• Dry Time, tack free – 6-8 hours
• Dry Time, foot traffic – 14-18 hours
• Dry Time, heavy traffic – 2-7 days
• Re-Coat Time Window – 10-16 hours
• Application Temperature – 50-80 deg F
• VOC Content – less than 5g/L
• Appearance, wet – clear, may show slight haze
• Appearance, dry – clear and high gloss

[return to top]

1040 Bond Koat 40% Solids Water Based Epoxy Primer

Key Features and Typical Benefits

• Low Viscosity allows for excellent substrate wetting and penetration.
• It provides a superior bond to concrete, making it an ideal primer for many other coatings.
• Fast cure times and low odor make this a concrete contractor’s favorite primer.
• Works well as a stand-alone, clear epoxy for interior applications.
• VOC compliant

Effective for many priming applications for most epoxies, urethanes, polyureas, and polyaspartic.

Specifications and Compliances

• Dried coating is USDA accepted
• Meets OTC, CARB, LADCO and SCAQMD VOC restrictions
• Solids Content – 40% by weight
• Dry Time, tack free – 20-40 minutes
• Dry Time, foot traffic – 6-12 hours
• Dry Time, heavy traffic – 2-5 days
• Minimum Re-Coat Time at 70 deg F – 4-6 hours
• Maximum Re-Coat Time at 70 deg F – 20-24 hours
• Application Temperature – 50-80 deg F
• VOC Content – Less than 20 g/L
• Appearance, wet – milky white
• Appearance, dry – clear and medium gloss

[return to top]

1055 Seal Koat 55% Solids Water Based Epoxy

Key Features and Typical Benefits

• Low viscosity allows for excellent substrate wetting and penetrations.
• It provides superior resistance to many common chemicals and solvents.
• Excellent abrasion resistance that rivals many solvent-based products.
• High gloss and low odor make this ideal for many interior applications.
• VOC compliant

Recommended for many interior applications where a low odor, abrasion-resistant coating is required.

Specifications and Compliances

• Dried coating is USDA accepted
• Meets OTC, CARB, LADCO and SCAQMD VOC restrictions
• Solids Content – 55% by weight
• Dry Time, tack free – 20-24 minutes
• Dry Time, foot traffic – 6-12 hours
• Dry Time, heavy traffic – 2-5 days
• Re-Coat Time Window – 4-6 hours
• Application Temperature – 50-80 deg F
• VOC Content – less than 20 g/L
• Appearance, wet – milky white
• Appearance, dry – clear and high gloss

[return to top]

SureFinish | Industrial Acrylic Wax Floor Finish

SureCrete Design Products SureFinish industrial floor wax is in both a gloss and matte finish in 1 gallon and 5-gallon packages. SureFinish provides a slip resistant floor finish with excellent scuff and scratch resistance helping to ensure maximum durability with a minimum of maintenance on old and new floor coatings.

Specifications and Properties of SureFinish Industrial Acrylic Wax Floor Finish from SureCrete Design Products

Coverage: 1,500 – 3,000 square foot per gallon per coat (varies depending substrate and application method)
VOC Rating: 0 g/L
Shelf Life: one year in original unopened container
Slip Resistance: Meets ASTM 2047 standard for slip resistance in floor coatings. The addition of SureFinish to nearly any surface will increase slip resistance.

[return to top]

Cherry Wax | Cherry Scented Water Based Acrylic Floor Wax

Key Features and Typical Benefits

• Pleasant cherry scent is less abrasive than many similar waxes.
• It provides superior sheen and resistance to abrasion and scuffing.
• Also available in a matte sheen.
• Non-flammable, non-combustible, non-corrosive and non-hazardous.
• Easy to use, great coverage.
• It contains zero VOC content.

Recommended Applications:

• Acid Stained Floors
• Over Metallic FX
• Kolour Dyed Floors

Typical Properties

• Solids Content – 21% by weight
• Dry Time, tack free – 1-2 hours
• Dry Time, foot traffic – 12-24 hours
• Dry Time, heavy traffic – 24-48 hours
• Recoat Time Window – 1-3 hours
• Application Temperature – 50-80 deg F
• VOC Content – zero g/L
• Appearance, wet – milky white
• Appearance, dry – clear, high gloss or matte sheen

[return to top]

Top Koat | Cherry Scented Water Based Acrylic Floor Wax

Key Features and Typical Benefits:

• Cherry scented
• High solids provides superior protection and resistance to abrasion and scuffing
• Non-flammable, non-combustible, non-corrosive and non-hazardous
• Contains zero VOC

Recommended Applications:

• Acid Stained Floors
• Over Metallic FX
• Kolour Dyed Floors

Typical Properties

• Solids Content – 28% by weight
• Dry Time, tack free – 1-2 hours
• Dry Time, foot traffic – 12-24 hours
• Dry Time, heavy traffic – 24-48 hours
• Recoat Time Window – 1-3 hours
• Application Temperature – 50-80 deg F
• VOC Content – zero g/L
• Appearance, wet – milky white
• Appearance, dry – clear, high gloss or matte sheen

[return to top]

SureGrip | Traction Additive for Slip Resistant Non-Skid Floors

The spherical shape of SureGrip provides a smoother feel than most other slip resistant additives. SureGrip is available in both sealer additive and hand-broadcast formulations. SureGrip Additive is available in two different particle sizes, medium and fine. Heavy-Duty = 840 microns or 20 mesh. Regular = 300 microns or 50 mesh.

Specifications and properties of SureGrip Traction Additive from SureCrete Design Products

Coverage: 1 quart additive per 5 gallons of sealer, or approximately 200 square feet per container broadcast
VOC Rating: 0 g/L
Shelf Life: one year in original unopened container
Appearance: Fine white powder

[return to top]