Self Leveling Floor Underlayment Materials | Polished Wear Toppings Self Level – Floor Leveling Compound Products

Self-leveling underlayment systems to correct and level any subfloor. Choose the right cement self-level system or from the range of synthetic gypsum self-level systems as stand-alone subfloor level surfaces or for use below floor coverings. Polished self-level wear toppings with integral aggregates for beautiful self-leveling polished concrete floors. These underlayment and wear topping systems are manufactured by Schönox and available in North Carolina and South Carolina.

Schonox US Self Leveling Cement Underlayment System for up to three inches thickness

Cement Based Self-leveling Compound suitable on cement and gypsum-based substrates. Designed for fast leveling in interior and exterior areas. Schönox US can be installed above 1/8″ up to 3″. Water and frost resistance.

Information Links:

Schonox DSP Plus Polished Overlayment System with Aggregate

Wear Rated, Cement Based Self-Leveling Concrete Topping with larger aggregate. DSP PLUS provides an extremely dense and durable surface to be polished in interior and exterior areas. DSP PLUS can be installed at a minimum of 3/8″ up to 2″. Designed for a variety of applications over suitable concrete from retail environments, restaurants, public buildings, entryways and offices to warehouse or manufacturing areas with moderate industrial loads. Suitable as a decorative top coat.

Information Links:

Schönox AP Synthetic Gypsum Self Leveling Underlayment

Synthetic Gypsum Based Self-leveling Compound especially suitable on all gypsum and cement-based substrates as well as on mastic asphalts. Designed for refurbishment work in interior areas. Schönox AP can be installed up to 2″.

Information Links:

Schonox XM Cement Self Leveling Underlayment for up to one half inch thickness

Cement Based Self-Leveling Smoothing and Leveling Compound Characterized by good working properties, standard preparation, and cost-effective applications. Suitable for layers up to 1/2″. Ready for covering after approximately 4-24 hours. Schönox XM is designed for fast leveling, filling and smoothing of floors in interior areas. It is suited for Flexible coverings; plywood subfloors, wood floor, layer thickness above 1/8”; Ceramic tiles; Concrete and cement substrates; Gypsum substrates; Old substrates, such as ceramic tiles and terrazzo; Old water-resistant adhesive residues.

Information Links:

Schonox ZM Cement Self Leveling Underlayment for up to one-inch thickness

Cement Based Self-leveling Compound suitable on all cement and gypsum-based substrates. Moisture resistant Schönox ZM is designed for fast leveling, filling, and smoothing of floors in interior areas. SCHÖNOX ZM can be installed from 1/16” to up to 1″ thick.

Information Links:

Schönox AP Rapid Plus Synthetic Gypsum Self Leveling System

Self-leveling Compound based on Hybrid Active Dry Technology designed for deep pour, fast track installations on most substrates in interior areas such as apartment buildings. Schönox AP Rapid Plus can be installed above 1/8″ up to 3″, in small, well-defined areas without limitation. Combine AP Rapid Plus with the Renotex 3D material for floating subfloor installations with very high flexural and tensile strength.

Information Links:

Schönox APF Fiber Reinforced Synthetic Gypsum Self Leveling System

Schönox APF is a fiber-reinforced, synthetic gypsum-based self-leveling compound for wood floors and critical interior substrates. With embedded fibers that make reinforcement fabric unnecessary, Schönox APF can be used on: Timber floorboards, OSB board and plywood; Wood-cement boards; Substrates such as ceramic tile, terrazzo and sheet vinyl; Water-resistant adhesive residues; Concrete, cement and gypsum substrates; Rapid cement screed systems. Schönox APF can be installed to layer thicknesses of 1/8″ to 1″. Dust Reduced. Compressive Strength: 6200 PSI

Information Links:

Schönox ZM Rapid Fast Setting Self Level Underlayment System

Rapid setting self-leveling compound suitable on all cement and gypsum based substrates. Designed for leveling of floors under time pressure in interior areas. Many types of floor coverings can be laid after 1.5 hours. Schönox ZM Rapid can be installed from 1/16” to up to 1” thick.

Information Links:

Schönox DSP Self Leveling Wear Topping Polished Concrete Overlayment

Wear rated, cement-based self-leveling compound and concrete topping designed for a variety of applications over suitable concrete from retail environments, restaurants, public buildings, entry ways, offices to warehouse or manufacturing areas with moderate industrial loads. Schönox DSP provides an extremely dense and durable surface to be sealed or polished in interior and exterior areas. Schönox DSP can be installed above 1/8“ up to 2”.

Information Links:

Schönox AP Rapid Fast Drying Synthetic Gypsum Self Leveling Underlayment

Synthetic Gypsum Based Self-leveling Compound designed for fast track installations on most substrates in interior areas such as apartment complexes, assisted living facilities, and educational facilities. Schönox AP Rapid can be installed up to 1/2″, in small, well-defined areas without limitation.

Information Links:

Schonox S1500 Self Leveling Underlayment System

Cement Based Self-Leveling Compound Suitable on all cement and gypsum substrates. May be installed in depth ranging from 1/8″ to 1 1/2″ with minimal shrinkage. For interior use only. Ready for covering after approximately 4-24 hours. S 1500 is ideal for covering old flooring. S 1500 is ideal for every skill level of the installer.

Information Links:

Schönox Renotex 3D Reinforcement Fabric

This multi-dimensional reinforcement fabric is a component of the Schönox Renotex 3D System. Combined with Schönox AP Rapid Plus and suitable sound insulation underlayments over wood substrates, this system creates a floating construction for improving the Impact Sound Insulation and Sound Transmission Rate as well as Thermal Insulation. The Schönox Renotex 3D System is a self-bearing, fire rated construction following the relevant standards of construction in the Multi-Family, Student Housing, or Senior Living markets.

Information Links:

Self Leveling Floor Underlayment Materials | Polished Wear Toppings Self Level – Floor Leveling Compound Products

Self-leveling underlayment systems to correct and level any subfloor. Choose the right cement self-level system or from the range of synthetic gypsum self-level systems as stand-alone subfloor level surfaces or for use below floor coverings. Polished self-level wear toppings with integral aggregates for beautiful self-leveling polished concrete floors. These underlayment and wear topping systems are manufactured by Schönox and available in North Carolina and South Carolina.

Additional information about self-leveling underlayment material systems for subfloor repair anywhere in North Carolina and South Carolina. Cement self-level underlayment and synthetic gypsum self-leveling subfloor underlayment for repair and restoration of interior floors.

Schonox US Self Leveling Underlayment System

Technical Data

Compressive Strength: 4,250 psi

Coverage: Approx. 55-65 sq.ft. per unit at a thickness of 1/8″

Emicode EC 1PLUS Regulated: very low emission

LEED

IEQ 4.3 Low-Emitting Materials-Flooring Systems, 1 point

MR 1.1 Building Reuse Maintain Existing Walls, Floors and Roof, up to 3 points

MR 1.2 Building Reuse Interior-Maintain Existing Interior Nonstructural Elements, 1 point

Pot Life: Approx. 40 minutes

Ready for Covering: For floor covering products after approx. 24 hours up to 1/4″ thickness, after 48 hours up to 3/8″ thickness; For tile or stone after approx. 4 hours

Shelf Life: 12 months

Working Temperature: Not below 41°F floor temperature

Color: Grey

Packsize: 55lb. net weight in paper bags

Packaging: 42/pallet

Product characteristics

  • EMICODE EC 1PLUS R: very low emission
  • for interior and exterior use
  • water and frost resistant, no moisture
  • vapor emission limitations on properly prepared concrete
  • self-leveling
  • suitable on underfloor heating systems
  • low shrinkage
  • pumpable
  • suitable for castor wheel loadings
  • layer thicknesses above 1/8“ up to 3“
  • tested in accordance with ASTM C1708
  • exceeds minimum Ff/Fl requirements of ASTM and ACI when installed in accordance with the guidelines

Applications

SCHÖNOX US is suitable for filling, smoothing and leveling of substrates floor leveling compound:

  • under flexible coverings
  • under interior wood floor, layer thickness at least 1/4“
  • under ceramic tiles and stone
  • as well as for filling, smoothing and leveling of unheated, cement based substrates under: SCHÖNOX Moisture Mitigation Systems

Substrates

SCHÖNOX US is suitable on:

  • concrete, cement substrates
  • gypsum substrates
  • OSB board, plywood (well screwed down or bonded) prior to install flexible coverings
  • old substrates such as ceramic tiles and terrazzo
  • old, water-resistant adhesive residues

Technical data

pot life: approx. 40 minutes at 68°F

ready for foot traffic: approx. 4 hours

ready for covering: after approx. 24 hours up to 1/4”, after approx. 48 hours up to 3/8“

for ceramic tiles: when walkable

working temperature: 41°F – 90°F

coverage per unit: approx. 55 – 65 sq.ft. at 1/8“ (depending on substrate conditions and aggregate used)

compressive strength (ASTM C109): 4250 psi / 25 N/mm² / 300 kg/cm2  after 28 days, 2000 psi / 12 N/mm² / 135 kg/cm² after 1 day

flexural strength (ASTM C348): approx. 1000 psi / 6 N/mm² after 28 days

tensile strength (ASTM C1583): above 350 psi / 2 N/mm² after 3 days

initial Set (ASTM C191): approx. 80 minutes

final Set (ASTM C191): approx. 95 minutes

cured density: 119 lbs. / cu.ft.

UL-classified in accordance with ASTM E84 (ANSI/UL 723):

Flame Spread 0; Smoke Development 0

Schonox DSP Plus Polished Overlay Material System with Aggregate

Technical Data

Compressive Strength

  • 7250 psi / 43 N/mm² / 580 kg/cm2 after 28 days
  • 4250 psi / 25 N/mm² / 300 kg/cm2 after 1 day

Coverage: Approx. 12 sq.ft. at 3/8“

LEED

  • EQc2 – 3 points
  • Low-Emitting Materials: MRc1 – up to 2 points
  • Life-Cycle Impact Reduction: MRc2 – 1 point
  • Environmental Product Declaration: MRc4 – 1 point
  • Material Ingredients

Pot Life: Approx. 30 minutes floor patch

Ready for Grinding: Approx. 24 hours

Shelf Life: 1 year unopened

Working Temperature: 41°F – 90°F

PRODUCT CHARACTERISTICS

EMICODE EC 1PLUS R: very low emission

For interior and exterior use

Moisture resistant

Self-leveling

Suitable on underfloor heating systems

Low shrinkage

Pumpable

Suitable for castor wheel loadings at 1/4″

Suitable for use as a commercial wear topping in industrial applications polishing minimum 3/8″

RECOMMENDED APPLICATION DETAILS

Schönox DSP is suitable for filling, smoothing and leveling of substrates under: Suitable sealers, densifiers and coatings when installed as a wear layer or polished topping

PACKAGING: 25 kg / 55 lb. net weight in paper bags

STORAGE: Store in cool and dry conditions.

Shelf life: 12 months unopened

DISPOSAL: Empty packaging and dispose of in accordance with federal, state and local waste disposal regulations.

VOC CONTENT: 0g/l (calculated), SCAQMD 1113

TECHNICAL DATA

Pot life: approx. 30 minutes at 68°F

Ready for foot traffic: after approx. 2-3 hours

Ready for covering: – after 24 hours up to 1/4″ thickness – after 48 hours up to 1/4″ thickness prior to applying suitable sealers, densifiers and coatings or prior to polishing – for ceramic tiles: when walkable

Working temperature: not below 41°F floor temperature

Coverage: approx. 25-30 sq.ft. per unit at a thickness of 1/4″ (depending on substrate conditions and aggregate used)

Compressive strength (ASTM C109/ mod – air cure only): approx. 40 N/mm² / 7250 psi at 28 days

Flexural strength (ASTM C348): approx. 10 N/mm² / 1500 psi at 28 days

Tensile strength (ASTM C1583): approx. 3 N/mm² / 450 psi after 3 days

Initial set (ASTM C191): approx. 80 minutes at 70°F

Final set (ASTM C191): approx. 95 minutes at 70°F

UL classified in accordance with ASTM E84 (ANSI/UL 723): Flame Spread 0; Smoke Development 0

Abrasion resistance (ASTM D4060): approx. 1.4 at 28 days

All values are approximate and are subject to local climatic fluctuations based upon conditions at 70°F with atmosphere of less than 65% relative humidity following the recommended mixing ratio. Do not install underlayment or topping before the substrate has dried thoroughly.

LEED V4 May help contribute to LEED v4 certification of projects in these categories:

EQc2 – 3 points Low-Emitting Materials

MRc1 – up to 2 points Life-Cycle Impact Reduction

MRc2 – 1 point Environmental Product Declaration

MRc4 – 1 point Material Ingredient

Schönox AP Self Leveling Underlayment

Technical Data floor leveling compound product

Compressive Strength: 30N/MM sq / 5800 psi at 28 days

Coverage: Approx. 60-70 sq.ft. per unit at a thickness of 1/8″

Emicode EC 1 PLUS: very low emission

LEED

IEQ 4.3 Low-Emitting Materials-Flooring Systems, 1 point

MR 1.1 Building Reuse Maintain Existing Walls, Floors and Roof, up to 3 points

MR 1.2 Building Reuse Interior-Maintain Existing Interior Nonstructural Elements, 1 point

MR 4 Recycled Content, up to 2 points

Pot Life: Approx. 30 minutes at 68˚F

Ready for covering: After approx. 16 hours up to 1/8″ layer-thickness

Shelf Life: 1 year unopened

Working Temperature: Not below 41°F floor temperature

Packaging: 55lb. net weight in paper bags

Storage: Store in cool and dry conditions

Product characteristics

  • EMICODE EC 1PLUS: very low emission
  • Benefits to Environment and Health
  • does not support mold growth
  • for interior use only
  • self-leveling
  • high hardness and strength
  • suitable for underfloor heating systems
  • layer-thickness above 1/16“ up to 2“
  • pumpable
  • very low shrinkage
  • free of cracks even in higher thicknesses
  • suitable for castor wheel loadings
  • low dust
  • very smooth surface
  • exceeds minimum Ff/Fl requirements of ASTM and ACI when installed in accordance with the guidelines tested in accordance with ASTM C1708

Applications

SCHÖNOX AP is suitable for filling, smoothing and leveling of substrates:

  • under flexible coverings
  • under wood floor, layer thickness at least 1/8“ floor patch (use elastic adhesives only)

Substrates

SCHÖNOX AP is suitable on:

  • gypsum substrates
  • concrete, cement substrates
  • old substrates such as ceramic tiles, terrazzo and sheet vinyl
  • old, water-resistant adhesive residues
  • OSB board, plywood (well screwed down and/or bonded) prior to install flexible coverings.

Technical data

pot life: approx. 30 minutes

ready for foot traffic: approx. 2 hours

ready for covering: after approx. 16 hours at 1/8“

working temperature: 41°F – 90°F

coverage per unit: approx. 60 – 70 sq.ft. at 1/8“ (depending on substrate conditions and aggregate used)

compressive strength (ASTM C109): 5800 psi / 35 N/mm² / 400 kg/cm2 after 28 days, 2100 psi / 13 N/mm² / 140kg/cm² after 1 day

flexural strength (ASTM C348): approx. 1400 psi / 8 N/mm² after 28 days

tensile strength (ASTM C1583) at 1/8“: above 400 / 2.5 N/mm² psi after 3 days

initial Set (ASTM C191): approx. 160 minutes

final Set (ASTM C191): approx. 200 minutes

cured density: 110 lbs. / cu.ft.

UL-classified in accordance with ASTM E84 (ANSI/UL 723):

Flame Spread 0; Smoke Development 0

Schonox XM Cement Self Leveling Underlayment System

Technical Data

Compressive Strength

4300 psi / 25 N/mm² / 300 kg/cm2 after 28 days

2000 psi / 12 N/mm² / 135 kg/cm² after 1 day

Coverage: Approx. 60 sq.ft. at 1/8“

LEED

EQc2 – 3 points

Low-Emitting Materials

MRc1 – up to 2 points

Life-Cycle Impact Reduction

MRc2 – 1 point

Environmental Product Declaration

MRc4 – 1 point

Material Ingredients

Pot Life: Approx. 30 minute

Ready for Covering: Approx. 16 hours up to 1/8”, Approx. 24 hours up to 1/4“

Shelf Life: 12 months unopened

Working Temperature: 41°F – 90°F

Packaging: 55lb. net weight in paper bags

Storage: Store in cool and dry conditions

Schönox XM is designed for fast leveling, filling and smoothing of floors in interior areas. It is suited for:

  • Flexible coverings
  • Wood floor, layer thickness above 1/8”
  • Ceramic tiles
  • Concrete and cement substrates
  • Gypsum substrates
  • Old substrates, such as ceramic tiles and terrazzo
  • Old water-resistant adhesive residues

Schönox XM can be installed from 1/16” up to 1/2”.

TECHNICAL DATA

Pot life: approx. 30 minutes

Ready for foot traffic: approx. 3 hours

Ready for covering: after approx. 24 hours at 1/8“, after approx. 48 hours at 1/4“

Working temperature: 41°F – 90°F

Coverage per unit: approx. 60 sq.ft. at 1/8“

Compressive strength: 4300 PSI

Schonox ZM Self Leveling Cement Underlayment System

Technical Data

Compressive Strength: 5,800 psi

Coverage: Approx. 60-70 sq.ft. per unit at a thickness of 1/8″

Emicode EC 1PLUS Regulated: very low emission

LEED

IEQ 4.3 Low-Emitting Materials-Flooring Systems, 1 point

MR 1.1 Building Reuse Maintain Existing Walls, Floors and Roof, up to 3 points

MR 1.2 Building Reuse Interior-Maintain Existing Interior Nonstructural Elements, 1 point

Pot Life Approx. 30 minutes

Ready for Covering: After approx. 24 hours up to 1/4″ layer-thickness

Shelf Life: 12 months unopened

Working Temperature: Not below 41°F floor temperature

Color: Grey

Packaging: 42/pallet

Packsize: 55lb. net weight in paper bags

Product characteristics

  • EMICODE EC 1PLUS R: very low emission
  • Benefits to Environment and Health
  • for interior use only
  • self-leveling
  • high hardness and strength
  • suitable on underfloor heating systems
  • layer thicknesses above 1/16“ up to 1“
  • pumpable
  • very low shrinkage
  • suitable for castor wheel loadings
  • moisture resistant (interior only), no moisture vapor emission limitations on properly prepared concrete
  • conforms with uSD 96/98/BC
  • exceeds minimum Ff/Fl requirements of ASTM and ACI when installed in accordance with the guidelines
  • tested in accordance with ASTM C1708
  • dust reduced

Applications

SCHÖNOX ZM is suitable for filling, smoothing and leveling of substrates:

  • under flexible coverings
  • under wood floor, layer thickness above 1/8“ (use elastic adhesives only)
  • under ceramic tiles
  • as well as for filling, smoothing and leveling of unheated, cement based substrates under: SCHÖNOX Moisture Mitigation Systems

Substrates

SCHÖNOX ZM is suitable on:

  • concrete, cement substrates
  • gypsum substrates
  • OSB board, plywood (well screwed or bonded) prior to install flexible coverings
  • old substrates such as ceramic tiles and terrazzo
  • old, water-resistant adhesive residues

Technical data

pot life: approx. 30 minute

ready for foot traffic: approx. 2 hours

ready for covering: after approx. 16 hours at 1/4”,  after approx. 48 hours at 3/8“

for ceramic tiles: when walkable

working temperature: 41°F – 90°F

coverage: approx. 60 – 70 sq.ft. at 1/8“ (depending on substrate conditions and aggregate used)

compressive strength (ASTM C109): 5800 psi / 35 N/mm² / 400 kg/cm2 after 28 days, 2400 psi / 15 N/mm² / 160 kg/cm² after 1 day

flexural strength (ASTM C348): approx. 1300 psi / 7 N/mm² after 28 days

tensile strength (ASTM C1583) at 1/8“: above 400 psi / 2.5 N/mm² after 3 days

initial Set (ASTM C191): approx. 60 minutes

final Set (ASTM C191): approx. 70 minutes

cured density: 116 lbs. / cu.ft.

UL-classified in accordance with ASTM E84 (ANSI/UL 723):

Flame Spread 0; Smoke Development 0

Schönox AP Rapid Plus Self Leveling Synthetic Gypsum

Technical Data

Compressive Strength: Approx. 40 N/mm² / 6300 psi at 28 days

Coverage: Approx. 14 sq.ft. at 1/2“ (depending on substrate conditions and aggregate used)

Emicode EC 1 PLUS: very low emission

LEED

EQc2 – 3 points Low-Emitting Materials

MRc1 – up to 2 points Life-Cycle Impact Reduction

MRc2 – 1 point Environmental Product Declaration

MRc3 – 1 point Sourcing of Raw Materials

MRc4 – 1 point Material Ingredients

Pot Life: Approx. 30 minutes at 68˚F

Ready for covering: after 16 hours at 1/2“ thickness, after 48 hours at 2“ thickness

Shelf Life: 1 year unopened

Working Temperature: 41°F – 90°F

Packaging: 25kg / 55lb. net weight in paper bags

Storage: Store in cool and dry conditions

AP RAPID PLUS PRODUCT DATA

PRODUCT CHARACTERISTICS

  • For interior use only
  • Designed for fast-track installations over critical substrates
  • Dust-reduced properties
  • Self-leveling
  • Suitable on underfloor heating systems
  • Very low shrinkage
  • Pumpable
  • Suitable for castor wheel loadings
  • Layer thicknesses above 1/8” up to 3”

ABOUT SCHÖNOX AP RAPID PLUS

Schönox AP Rapid Plus is suitable for filling, smoothing, and leveling of substrates under:

  • Flexible coverings
  • Wood floor, layer thickness above 1/8“

Suitable on:

  • Concrete and cement substrates
  • Gypsum substrates
  • Old floorings, such as ceramic tiles, terrazzo, sheet vinyl, rubber, and resilient floor coverings
  • Old, water-resistant adhesive residues
  • OSB board and plywood
  • In combination with decoupled Renotex® 3D System installation

TECHNICAL DATA

Pot life: approx. 30 minutes at 68°F

Ready for foot traffic: approx. 2-3 hours

Ready for covering: after 12-16 hours at 1/2“ thickness, after 48 hours at 2“ thickness

Working temperature: 41°F – 90°F

Coverage per unit: approx. 14 sq.ft. at 1/2“

Compressive strength (ASTM C109): 6300 psi after 28 days, 2400 psi after 1 day

Schönox APF Fiber Reinforced Self Leveling Underlayment Material

Technical Data

Compressive Strength: 6,200 psi

Coverage:Approx. 60-70 sq.ft. per unit at a thickness of 1/8″

Emicode EC 1 PLUS: very low emission PLUS

LEED

IEQ 4.3 Low-Emitting Materials-Flooring Systems, 1 point

MR 1.1 Building Reuse Maintain Existing Walls, Floors and Roof, up to 3 points

MR 1.2 Building Reuse Interior-Maintain Existing Interior Nonstructural Elements, 1 point

MR 4 Recycled Content, up to 2 points

Pot Life: Approx. 30 minutes

Ready for covering: After approx. 16 hours up to 1/8″ layer-thickness

Shelf Life: 12 months

Working Temperature: Not below 41°F floor temperature

Color: White

Packaging: 42/pallet

Packsize: 55lb. net weight in paper bags

Product characteristics

  • EMICODE EC 1PLUS: very low emission
  • does not support mold growth
  • for interior use only
  • self-leveling
  • low dust
  • high hardness and strength
  • suitable on underfloor heating systems
  • layer-thickness above 1/8“ up to 1“
  • pumpable
  • very low shrinkage
  • free of cracks even in higher thicknesses
  • suitable for castor wheel loadings
  • tested in accordance with ASTM C1708 exceeds minimum Ff/Fl requirements of ASTM and ACI when installed in accordance with the guidelines

Applications

SCHÖNOX APF is suitable for filling, smoothing and leveling of substrates:

  • under flexible coverings
  • under wood floor (use elastic adhesives only)

Substrates

SCHÖNOX APF is suitable on:

  • timber, OSB board, plywood (well screwed down and/or bonded)
  • old substrates such as ceramic tiles, terrazzo and sheet vinyl
  • old, water-resistant adhesive residues
  • concrete, cement substrates
  • gypsum substrates

Technical data

pot life: approx. 30 minutes

ready for foot traffic: approx. 3 hours

ready for covering: after approx. 16 hours, at 1/8“

working temperature: 41°F – 90°F

coverage per unit: approx. 60 – 70 sq.ft. at 1/8“ (depending on substrate conditions and aggregate used)

compressive strength (ASTM C109): 6200 psi / 40 N/mm² / 420 kg/cm2 after 28 days, 2400 psi / 16 N/mm² / 144 kg/cm² after 1 day

flexural strength (ASTM C348): approx. 1600 psi / 10 N/mm² after 28 days

tensile strength (ASTM C1583) at 1/8“: above 400 psi / 2.5 N/mm² after 3 days

initial Set ASTM C191): approx. 170 minutes

final Set (ASTM C191): approx. 200 minutes

cured density: 113 lbs. / cu.ft.

UL-classified in accordance with ASTM E84 (ANSI/UL 723):

Flame Spread 0; Smoke Development 0

Schönox ZM Rapid Cement Self Level Underlayment Floor Repair

Technical Data

Compressive Strength: 7,550 psi

Coverage: 60-70 sq.ft. per unit at a thickness of 1/8″

Emicode EC 1PLUS Regulated: very low emission

LEED

IEQ 4.3 Low-Emitting Materials-Flooring Systems, 1 point

MR 1.1 Building Reuse Maintain Existing Walls, Floors and Roof, up to 3 points

MR 1.2 Building Reuse Interior-Maintain Existing Interior Nonstructural Elements, 1 point

Pot Life: Approx. 25 minutes

Ready for Covering: After approx. 1.5-2 hours up to 3/8″ thickness prior to installing carpet, vinyl, and linoleum; Approx. 12 hours prior to installing wood floor, cork or rubber.

Shelf Life: 12 months unopened

Working Temperature: Not below 41°F floor temperature

Color: Grey

Packaging: 42/pallet

Packsize: 55lb. net weight in paper bags

Product characteristics

  • EMICODE EC 1PLUS R: very low emission
  • Benefits to Environment and Health
  • for interior use only
  • self-leveling
  • ready for covering after approx. 1.5 hours for many types of coverings
  • suitable or underfloor heating systems
  • high hardness and strength
  • layer thicknesses above 1/16“ up to 1“
  • pumpable
  • suitable for castor wheel loadings
  • suitable for forklift truck traffic above 1/8“
  • tested in accordance with ASTM C1708
  • exceeds minimum Ff/Fl requirements of ASTM and ACI when installed in accordance with the guidelines

Applications

SCHÖNOX ZM RAPID is suitable for filling, smoothing and leveling of substrates:

  • under flexible coverings
  • under ceramic tiles
  • under wood floor and coatings, layer thickness at least 1/8” (drying time at least 12 hours)

Substrates

SCHÖNOX ZM RAPID is suitable for filling, smoothing and leveling of:

  • concrete, cement substrates
  • old substrates such as ceramic tiles
  • old, water-resistant adhesive residues
  • gypsum substrates
  • OSB board, plywood (well screwed and/or bonded) prior to installing flexible coverings.

Technical data

pot life: approx. 25 minutes

ready for foot traffic: approx. 1 – 1.5 hours

ready for covering: after approx. 1.5 – 2 hours at 1/2“, after approx. 12 hours at 1/2“ prior to installing wood floor, cork, rubber or coatings

working temperature: 41°F – 90°F

coverage per unit: approx. 60 – 70 sq.ft. at 1/8” (depending on substrate conditions and aggregate used)

compressive strength (ASTM C109): 7550 psi / 50 N/mm² / 600 kg/cm2 after 28 days, 5000 psi / 30 N/mm² / 400 kg/cm² after 1 day

flexural strength (ASTM C348): approx. 1550 psi / 10 N/mm² after 28 days

tensile strength (ASTM C1583) at 1/8“: above 400 psi / 2.5 N/mm² / 400 psi after 3 days

initial Set (ASTM C191): approx.35 minutes

final Set (ASTM C191): approx. 45 minutes

cured density: 121 lbs. / cu.ft.

UL-classified in accordance with ASTM E84 (ANSI/UL 723):

Flame Spread 0; Smoke Development 0

Schönox DSP Wear Rated Polished Concrete Self Level Overlay Product

Technical Data

Compressive Strength (ASTM C109/mod – Air cure only): Approx. 40 N/mm² / 7250 psi at 28 days

Coverage: Approx. 28 sq.ft. per unit at a thickness of 1/4″

Emicode EC 1PLUS Regulated : very low emission

LEED

EQc2, Low-Emitting Materials: 1 to 3 points

MR Credit 1.1, Building Reuse-Maintain – Existing Walls, Floors and Roof: up to 3 points

MR Credit 1.2, Building Reuse-Maintain – Existing Interior Nonstructural Elements: 1 point

Pot Life: Approx. 30 minutes at 68°F

Ready for Coverage: After 24 hours up to 1/4“ thickness; After 48 hours up to 1/4“ thickness prior to apply suitable sealers, densifiers and coatings or prior to start the polishing process

For ceramic tiles: when walkable

Ready for Traffic: After approx. 2-3 hours

Shelf Life: 1 year unopened

Storage: Store in cool and dry conditions

Working Temperature: Not below 41°F floor temperature

Packaging: 25kg / 55lb. net weight in paper bags

Product characteristics

  • EMICODE EC 1PLUS R: very low emission
  • for interior and exterior use
  • moisture resistant
  • self-leveling
  • suitable on underfloor heating systems
  • low shrinkage
  • pumpable
  • suitable for castor wheel loadings
  • suitable for use as a commercial wear topping in industrial applications (rubber wheeled traffic) above ¼”
  • suitable for polishing above 3/8”
  • tested in accordance with ASTM C1708
  • exceeds minimum Ff/Fl requirements of ASTM and ACI when installed in accordance with the guidelines

Applications

SCHÖNOX DSP is suitable for filling, smoothing and leveling of substrates under:

  • suitable sealers, densifiers and coatings
  • when installed as a wear layer or concrete topping as well as for filling, smoothing and leveling of unheated, cement based substrates under: SCHÖNOX Moisture Mitigation Systems

Substrates

SCHÖNOX DSP is suitable on:

  • concrete, cement substrates (CSP 3 when installed for polishing)

Technical data

pot life: approx. 30 minutes

ready for foot traffic: approx. 2 – 3 hours

ready for covering: after approx. 24 hours at 1/4“, after approx. 24 – 48 hours at 3/8“ prior to apply suitable sealers or to start polishing

working temperature: 41°F – 90°F

coverage per unit: approx. 25 – 30 sq.ft. at 1/4“ (depending on substrate conditions and aggregate used)

compressive strength (ASTM C109): 7250 psi / 43 N/mm² / 580 kg/cm2 after 28 days, 2000 psi / 12 N/mm² / 135 kg/cm² after 1 day

flexural strength (ASTM C348): approx. 1500 psi / 10 N/mm² after 28 days

tensile strength (ASTM C1583) above 450 psi / 2.5 N/mm² / after 3 days

initial Set (ASTM C191): approx. 80 minutes

final Set (ASTM C191): approx. 95 minute

UL-classified in accordance with ASTM E84 (ANSI/UL 723): Flame Spread 0; Smoke Development 0

abrasion resistance (ASTM D4060): approx. 1.4 at 28 days

cured density: 121 lbs. / cu.ft

Schönox AP Rapid Fast Track Self Leveling Underlayment Floor Repair

Technical Data

Compressive Strength: 5800 psi / 35 N/mm² / 400 kg/cm2 after 28 days, 2400 psi / 15 N/mm² / 160 kg/cm² after 1 day

Coverage: Approx. 60 sq.ft. at 1/8“ (depending on substrate conditions)

Emicode EC 1 PLUS: very low emission

LEED

MRc1 – up to 2 points Life-Cycle Impact Reduction

MRc2 – 1 point Environmental Product Declaration

MRc3 – 1 point Sourcing of Raw Materials

MRc4 – 1 point Material Ingredients

Pot Life: Approx. 30 minutes at 68°F

Ready for covering: After 6 hours at 1/4“ thickness, After 24 hours at 1/2“ thickness

Shelf Life: 1 year unopened

Working Temperature: 41°F – 90°F

Packaging: 25kg / 55lb. net weight in paper bags

Storage: Store in cool and dry conditions

Product characteristics

EMICODE EC 1PLUS R: very low emission based on Hybrid Active Dry Technology

For interior use only

Designed for fast track installations over critical substrates

  • low dust
  • self-leveling
  • suitable on underfloor heating systems
  • very low shrinkage
  • pumpable
  • suitable for castor wheel loadings
  • layer thicknesses above 1/16“ up to 1/2“

Applications

SCHÖNOX AP RAPID is suitable for filling, smoothing and leveling of substrates under:

  • flexible coverings
  • wood floor, layer thickness at least 1/8“ (use elastic adhesives only)

Substrates

SCHÖNOX AP RAPID is suitable on:

  • concrete
  • cement substrates
  • gypsum substrates
  • old floorings such as ceramic tiles, terrazzo and sheet vinyl/rubber/resilient floor coverings
  • old, water-resistant adhesive residues
  • OSB board, plywood (well screwed down and/or bonded)

Technical data

pot life: approx. 30 minutes at 68°F

ready for foot traffic: approx. 2 – 3 hours

ready for covering: after 6 hours at 1/4“ thickness, after 24 hours at 1/2“ thickness

working temperature: 41°F – 90°F

coverage per unit: approx. 60 sq.ft. at 1/8“ (depending on substrate conditions)

compressive strength (ASTM C109): 5800 psi / 35 N/mm² / 400 kg/cm2 after 28 days, 2400 psi / 15 N/mm² / 160 kg/cm² after 1 day

flexural strength (ASTM C348): approx. 7 N/mm² / 1300 psi after 28 days

tensile strength (ASTM C1583): approx. 2 N/mm² / 350 psi after 3 days

initial Set (ASTM C191): approx. 60 minutes at 70°F

final Set (ASTM C191): approx. 65 minutes at 70°F

cured density: 119 lbs. / cu.ft.

UL-classified in accordance with ASTM E84 (ANSI/UL 723):

Flame Spread 0; Smoke Development 0

Schonox S1500 Self Leveling Underlayment System Cement Based

Technical Data

Compressive Strength: 4900 psi / 35 N/mm² after 28 days

Coverage: Approx. 50 sq.ft. per unit at a thickness of 1/8″

LEED

  • EQc2 – 3 points
  • Low-Emitting Materials: MRc1 – up to 2 points
  • Life-Cycle Impact Reduction: MRc2 – 1 point
  • Environmental Product Declaration: MRc4 – 1 point

Pot Life: Approx. 30 minutes at 68˚F

Ready for Covering: Approx. 24 hours up to 1/4”, Approx. 48 hours up to 3/8“

Shelf Life: 1 year unopened

Working Temperature: 41°F – 90°F

Packaging: 55lb. net weight in paper bags

Storage: Store in cool and dry conditions

PRODUCT CHARACTERISTICS

  • For interior use only
  • Self-leveling
  • Suitable on underfloor heating systems
  • Low shrinkage
  • Pumpable
  • Suitable for castor wheel loadings
  • Layer thicknesses above 1/8” up to 1-1/2”
  • Tested in accordance with ASTM C1708
  • Exceeds minimum Ff/Fl requirements of ASTM and ACI when installed in accordance with the guidelines

RECOMMENDED APPLICATION DETAILS

Schönox S 1500 is suitable for filling, smoothing and leveling of substrates under:

  • Flexible coverings
  • Floor leveling compounds
  • Interior wood floor, layer thickness of at least 1/4”
  • Ceramic tiles and stone

Schönox S 1500 is suitable on:

  • Concrete, and cement substrates
  • Gypsum substrates
  • Old floorings such as ceramic tiles and terrazzo
  • Old, water-resistant adhesive residues

PRIMING

For porous substrates such as concrete and cement substrates, prime with Schönox VD (1:3) or KH FIX. For non porous, smooth, sound substrates such as ceramic tiles, and old water resistant adhesive residues prime with Schönox SHP. For gypsum substrates, sanded and vacuumed, prime with Schönox KH Fix.

PACKAGING

  • net weight in paper bags

MIXING RATIO

  • Mix each 55lb. bag with 4.5 liters / 4.7 quarts of water
  • Do not overwater! Foam while mixing, or settling of the sand aggregate while placing, indicates overwatering.

TECHNICAL DATA

  • Pot life: approx. 30 minutes at 68°F
  • Ready for foot traffic: approx. 3 hours
  • Ready for covering: after approx. 24 hours up to 1/4”; after approx. 48 hours up to 3/8”; for ceramic tiles: when walkable
  • Working temperature: 41°F – 90°F
  • Coverage per unit: approx. 27 sq.ft. at 1/4” (depending on substrate conditions)
  • Compressive strength (ASTM C109): 4900 psi / 35 N/mm² after 28 days
  • Flexural strength (ASTM C348): approx. 1150 psi / 6 N/mm² after 28 days
  • Tensile strength (ASTM C1583): above 350 psi / 2 N/mm², after 3 days at 1/8”
  • Initial Set (ASTM C191): approx. 80 minutes
  • Final Set (ASTM C191): approx. 95 minutes
  • Cured density: 121 lbs. / cu.ft.
  • Flammability (ASTM E84): Flame Spread 0; Smoke Development 0

Schönox Renotex 3D Floating Floor Self Level Underlayment Reinforcement Fabric

Technical Data

Material

  • Front – Glass fiber
  • Back – Glass fiber
  • Chain binding – Textured polyester
  • Pile warp – Polyethylene

Coverage per Roll :Approx. 540 sq. ft

Roll Dimensions

  • 2m x 25m
  • 74” x 984.25”
  • 56’ x 82.02’

Rolls per Pallet: 6

Weight per Roll: 73 lbs.